Skip to content

Uses of Ultrasound: Medical Scans, Crack Detection and Sonar

Learn what ultrasound is, why some of it reflects at every boundary between materials, and how echo timing is used in pregnancy scans, crack detection in metal and sonar. Worked examples find depths from echo times, with the key step of halving the distance.

Published · 7 min read

On this page

Ultrasound is sound with a frequency above about 20 000 Hz (20 kHz). That is the top of the range people can hear. Apart from that, it is an ordinary sound wave: a longitudinal wave that needs a medium.

Ultrasound is useful because of what happens at a boundary between two materials, such as fat and muscle, or steel and air. Part of the wave reflects back as an echo, and the rest carries on. A probe sends out a short pulse and times each echo that returns. Since the pulse travels to the boundary and back, the depth of the boundary is:

depth=speed×time2\text{depth} = \frac{\text{speed} \times \text{time}}{2}

That one idea runs through the three main uses: medical scanning, finding hidden cracks in metal, and sonar under water.

Why does ultrasound reflect at boundaries?

When a wave reaches a boundary between two different materials, it is partially reflected. How much reflects depends on how different the two materials are. These figures are rough:

  • Between two soft tissues, such as fat and muscle, only about 1% of the energy reflects. Most of the pulse carries on, so deeper boundaries can still send back echoes.
  • Between soft tissue and bone, roughly 40% reflects. Little ultrasound gets through bone, so it casts a shadow.
  • Between skin and air, more than 99% reflects. Almost nothing gets through.

That last point is why a sonographer spreads gel on the skin before a scan. The gel fills the tiny air gap between the probe and the body, so the ultrasound can get in.

Why use such high frequencies?

Medical scanners often use frequencies of a few megahertz. The wave equation, v=fλv = f\lambda, shows why. In soft tissue, sound travels at about 1540 m/s. At 5.0 MHz, the wavelength is:

λ=vf=15405.0×106=3.1×10−4 m\lambda = \frac{v}{f} = \frac{1540}{5.0 \times 10^{6}} = 3.1 \times 10^{-4} \text{ m}

That is about 0.3 mm. A wave cannot show much detail smaller than its wavelength, so a short wavelength gives a sharp image. A 1000 Hz sound in the same tissue would have a wavelength of 1.54 m, far too long to show anything inside a body.

How does a medical ultrasound scan work?

A probe on the skin sends pulses into the body and listens between them. Each boundary inside returns its own echo. A computer uses the time of each echo, and the speed in tissue, to work out how deep each boundary lies. It builds these depths into a picture on the screen, many times a second, so doctors can watch a heart beating or a baby moving.

Worked example 1: the thickness of a kidney

A probe sends a pulse into a patient's back. Echoes return from the front and back surfaces of a kidney after 39 µs and 91 µs. Take the speed of sound in soft tissue as 1540 m/s. How deep is each surface, and how thick is the kidney?

Convert the times: 39 µs = 39×10−639 \times 10^{-6} s and 91 µs = 91×10−691 \times 10^{-6} s

First surface: depth=1540×39×10−62=0.030\text{depth} = \dfrac{1540 \times 39 \times 10^{-6}}{2} = 0.030 m

Second surface: depth=1540×91×10−62=0.070\text{depth} = \dfrac{1540 \times 91 \times 10^{-6}}{2} = 0.070 m

Thickness: 0.070−0.030=0.0400.070 - 0.030 = 0.040 m

Answer: the surfaces are 3.0 cm and 7.0 cm below the skin, so the kidney is about 4.0 cm thick.

Why is ultrasound safer than X-rays for scanning a baby?

X-rays are ionising radiation. They can knock electrons out of atoms and damage the DNA in cells. Cells in an unborn baby divide quickly, which makes them especially sensitive to that damage.

Ultrasound is a sound wave, not ionising radiation. At the power used for scanning, it has been used for decades with no known harm, so it is the normal way to check on a baby in the womb, from London to Lahore. Doctors still scan only when there is a medical reason.

Ultrasound is also better at the job. X-rays pass through soft tissue with little difference between organs, so they mainly show bones. Ultrasound shows the boundaries between soft tissues, and it shows movement live. It cannot see well through bone or air, so it is little use for looking inside an adult's skull or deep into the lungs.

How does ultrasound find cracks in metal?

Engineers send ultrasound into metal parts they cannot cut open: railway rails, welds in oil and gas pipelines, and aircraft wings. A pulse should travel through the metal and echo from the far side. A hidden crack is a boundary between metal and air, so it sends back an extra, earlier echo. Testing that leaves the part undamaged like this is called non-destructive testing.

Worked example 2: a crack in a steel plate

A steel plate is 10.0 cm thick. Sound travels through this steel at about 5900 m/s, a typical value.

(a) When should the echo from the far side return?

(b) An extra echo returns after only 12 µs. How deep is the crack?

(a) The pulse travels 2×0.100=0.2002 \times 0.100 = 0.200 m in total.

t=sv=0.2005900=3.4×10−5t = \dfrac{s}{v} = \dfrac{0.200}{5900} = 3.4 \times 10^{-5} s, or about 34 µs

(b) depth=5900×12×10−62=0.035\text{depth} = \dfrac{5900 \times 12 \times 10^{-6}}{2} = 0.035 m

Answer: the far-side echo should arrive after about 34 µs. The early echo shows a crack about 3.5 cm below the surface.

How do sonar and echo sounding work?

Ships use the same timing under water. An echo sounder on the hull sends pulses of high-frequency sound, often ultrasound, straight down and times the echoes. The echo from the seabed gives the depth of the water. A shoal of fish, a wreck or a submarine in the way returns an earlier echo. Navies, survey ships and fishing boats from Norway to Sri Lanka all use this. Bats and dolphins find their food in a similar way, with their own high-pitched calls.

Worked example 3: fish and seabed

A fishing boat sends a pulse straight down. One echo returns after 0.040 s and another after 0.12 s. Sound travels at about 1500 m/s in seawater. How deep are the fish and the seabed?

Fish: depth=1500×0.0402=30\text{depth} = \dfrac{1500 \times 0.040}{2} = 30 m

Seabed: depth=1500×0.122=90\text{depth} = \dfrac{1500 \times 0.12}{2} = 90 m

Answer: the shoal is 30 m down, in water 90 m deep.

Ultrasound has other uses too. Ultrasonic cleaning baths, often working at 20 to 40 kHz, shake dirt off jewellery and dental instruments.

How can you explore ultrasound?

In our sound waves and oscilloscope simulation, pick Ultrasound from the Set-ups menu. The Frequency card is now labelled Ultrasound, and the Wavelength card shows a very short wavelength. Then choose Water under What the sound travels through. The frequency stays the same, but the Speed of sound card goes up, so the wavelength gets longer. A speed of sound and echoes simulation is planned.

Common mistakes

  • Forgetting to halve. The echo time covers the trip there and back.
  • Skipping the unit conversion. 1 µs is 10−610^{-6} s, and 1 MHz is 10610^{6} Hz.
  • Using the speed in air for the body or for steel. Use the speed in the material the pulse is travelling through.
  • Calling ultrasound radiation like X-rays. It is a sound wave and it does not ionise.
  • Saying all the ultrasound reflects. At most boundaries inside the body only a small part reflects, which is why deeper boundaries still show up.

Key points

  • Ultrasound is sound above about 20 kHz, too high for people to hear.
  • At a boundary between two materials, part of the ultrasound reflects and the rest carries on.
  • Depth = speed × time ÷ 2, because the pulse goes there and back.
  • Medical scans use it because it is not ionising and it shows soft tissue. Its short wavelength gives fine detail.
  • Industry uses it to find hidden cracks, and ships use it to measure depth and find objects under water.