Gas Pressure and Volume: pV = Constant, Temperature and the Kelvin Scale
Explain gas pressure with particle collisions, predict what heating or squeezing a gas does, use p₁V₁ = p₂V₂ for a syringe, a bike pump and a weather balloon, and convert between degrees Celsius and kelvin.
Published · 8 min read
On this page
A gas presses on the walls of its container because its particles never stop hitting them. The pressure goes up if the particles strike the walls more often or harder. There are two simple ways to make that happen:
- Heat the gas in a fixed volume. The particles speed up, so they hit the walls more often and with more force.
- Squeeze the gas into a smaller volume at a fixed temperature. The particles keep the same average speed, but they have less space to cross, so each part of the wall is struck more often.
For a fixed mass of gas at constant temperature, pressure × volume stays the same:
So if you halve the volume, the pressure doubles. This guide explains both effects, the kelvin scale, and why a bike pump gets warm.
Where does gas pressure come from?
The particles in air move in random directions at roughly 500 m/s at room temperature. Every time one bounces off a wall, it pushes on that wall for an instant. Billions upon billions of these impacts every second blend into a steady force. On average the sideways parts of these pushes cancel, so the overall force acts at right angles to the wall. Divide that force by the wall's area and you have the pressure.
The air around you exerts about 100 000 Pa, which is 100 000 N on every square metre. You do not feel crushed because the fluids in your body, and the air in your lungs, push outwards just as hard. To compare gas particles with those in solids and liquids, open the states of matter simulation.
What happens when you heat a gas in a fixed volume?
Raising the temperature raises the average kinetic energy of the particles. Faster particles reach the walls more often, and each collision gives a bigger push. So the pressure rises.
You see this in everyday life:
- Aerosol cans carry a warning not to leave them in sunlight or near heat. The gas pressure inside could rise until the can bursts.
- Car tyres should be checked when cold. After a long drive on a hot motorway in Spain, the air inside is warmer and the gauge reads higher.
- A sealed, empty plastic bottle placed in a freezer caves in slightly. The air inside cools, its pressure falls, and the air outside pushes the sides in.
What is absolute zero, and how do you convert to kelvin?
The colder a gas, the slower its particles move. At absolute zero, −273 °C, the particles would have the lowest possible kinetic energy. Nothing can be cooled below this.
The kelvin scale starts at absolute zero. A change of 1 K is the same size as a change of 1 °C, so converting only means adding or subtracting 273:
| Temperature | Degrees Celsius | Kelvin |
|---|---|---|
| Absolute zero | −273 °C | 0 K |
| Liquid nitrogen boils | −196 °C | 77 K |
| Ice melts | 0 °C | 273 K |
| Human body | 37 °C | 310 K |
| Water boils (at normal air pressure) | 100 °C | 373 K |
Write kelvin as "K", not "°K".
What happens when you squeeze a gas at constant temperature?
Push a gas into half the space, keeping its temperature the same. The particles' average speed is unchanged, so each collision is no harder than before. But they now cross a smaller box, so each part of the wall gets hit twice as often. The pressure doubles.
This is the rule , often called Boyle's law, though your course may not use the name. It holds only when two things stay fixed: the mass of gas (no leaks) and its temperature.
On a graph of p against V, the line is a curve that falls fast at small volumes and flattens at large ones. It never touches either axis. Plot p against 1/V instead and the points lie along a straight line, which, if extended, reaches the origin. This shows that p is inversely proportional to V.
Worked example 1: a sealed syringe
A student in Toronto traps 60 cm³ of air in a syringe at 100 kPa and seals the nozzle. They press the plunger gently, giving the air time to stay at room temperature, until the volume is 20 cm³. Find the new pressure.
Given: = 100 kPa, = 60 cm³, = 20 cm³
Equation: , so
Substitution:
Answer: = 300 kPa
The volume became a third as big, so the pressure became three times as big.
Worked example 2: a bike pump
A cyclist in Amsterdam pumps up a tyre. The pump's barrel holds 150 cm³ of air at 100 kPa. The air in the tyre is at 350 kPa. That is the total pressure: a tyre gauge shows only the part above the 100 kPa of the atmosphere. The valve opens only when the air in the barrel reaches the tyre's pressure. Assuming the temperature stays the same, what is the volume of air in the barrel at that moment?
Given: = 100 kPa, = 150 cm³, = 350 kPa
Equation:
Substitution:
Answer: = 43 cm³ (2 significant figures)
So about 70% of each stroke only squeezes the air in the barrel. No air enters the tyre until the last part of the push. That is why pumping gets harder as the tyre fills.
In a real, quick stroke the air also warms up (see the next section), so its pressure climbs faster and the valve opens a little earlier, at roughly 60 cm³ instead of 43 cm³. Exam questions that say "the temperature stays constant" want the 43 cm³ answer.
Worked example 3: a weather balloon
Meteorologists in Australia launch a weather balloon holding 5.0 m³ of helium at ground level, where the air pressure is 100 kPa. The helium pressure stays close to the pressure of the air around it. Estimate the balloon's volume at a height where the air pressure is 25 kPa, assuming the helium's temperature does not change.
Given: = 100 kPa, = 5.0 m³, = 25 kPa
Equation:
Substitution:
Answer: = 20 m³
The real balloon is noticeably smaller. At about 10 km up, the air is near −50 °C, so the helium cools, and pV = constant only works at a fixed temperature. Higher still, the balloon stretches until the rubber bursts, and the instruments return on a parachute.
You can explore pressure, volume and temperature together in the gas laws and particles simulation.
Why does pumping up a tyre make the pump warm?
Feel the bottom of a bike pump's barrel after a dozen quick strokes. It is warm. When you push the plunger, you exert a force through a distance, so you do work on the gas. The particles that hit the moving plunger bounce back faster, like a tennis ball hit by a racket swinging towards it. The average kinetic energy of the particles goes up, so the gas gains internal energy and gets hotter.
The reverse also happens. Air rushing out of a tyre valve expands and pushes the outside air away, so it does work and cools. That is why the escaping air feels cold.
Common mistakes
- Using degrees Celsius for proportion. A gas at 40 °C is not "twice as hot" as one at 20 °C. Convert to kelvin first.
- Forgetting the conditions. pV = constant needs a fixed mass of gas at a fixed temperature.
- Saying compressed particles hit harder. At constant temperature they hit more often, not harder.
- Mixing units. Do not put kPa on one side of the equation and Pa on the other.
- Assuming a gauge shows the total pressure. A tyre gauge leaves out the atmosphere's share.
- Saying the particles expand when a gas is heated. The particles move faster; they do not grow.
Key points
- Gas pressure is caused by particles striking the walls, which produces a force at right angles to each surface.
- Heating a gas at constant volume raises its pressure, because the particles move faster.
- At constant temperature, a smaller volume means more frequent collisions and a higher pressure: .
- A graph of p against 1/V is a straight line through the origin.
- T (in K) = θ (in °C) + 273, and absolute zero is −273 °C, or 0 K.
- Doing work on a gas, as in a bike pump, raises its temperature.