Skip to content

Measurement and skills simulation

Vernier Caliper Simulation

Close a steel vernier calliper on a brass cylinder, a glass marble or a coin, or open it inside a washer's hole. A magnifier rides on the vernier and lights up the line that lines up, so you can see exactly where each digit of the reading comes from, zero errors included.

Loading simulation…
Show symbols for

Predict first

Question 1 of 3

The jaws close on a brass cylinder. The vernier zero stops just past the 2.3 cm mark of the main scale, and vernier line 6 lines up exactly with a main-scale mark. The least count is 0.01 cm. What diameter does the calliper show?

Try this

  1. 1With the starting brass cylinder, find the glowing line in the magnified view. Check that 2.3 cm + 6 × 0.01 cm gives the Reading card's value.
  2. 2Press the single › button one step at a time. Which vernier line glows after each press, and how much does each press add to the reading?
  3. 3Choose Nothing (jaws empty) in the In the jaws menu and press Close. Then pick Negative under Zero error (Left of 0 on the Punjab course) and work out the error from the closed jaws before you look at the cards.
  4. 4Choose Steel washer (inside jaws) and press Open. Why do these jaws have to open, not close, to measure the hole?
  5. 5Switch to Practice. Press Check zero to read the zero error, then Back to put the object in the jaws. Read the scales, type the true size and press Check. Press New for another task.

What this simulation shows

A vernier calliper (US spelling: caliper) measures small lengths, such as the width of a coin, about ten times more finely than a ruler. In this simulation you slide the jaw yourself, and a magnifier fixed to the sliding scale shows the two scales up close. When the jaw stops, the vernier line that sits exactly on a main-scale mark glows, so every reading can be checked by eye.

Each scale line is drawn to scale from the reading, never painted on afterwards. If the magnifier says line 4 lines up, line 4 really is the only line on a mark.

Reading the two scales

The beam carries the main scale, marked in millimetres and numbered in centimetres. The sliding jaw carries a short vernier scale. Take a reading in two steps.

  1. Find the vernier zero. The last main-scale mark it has passed is the main scale reading. In the magnifier it turns orange.
  2. Look along the vernier for the one line that matches a main-scale mark. Its number tells you how many least counts to add.

reading=main scale reading+n×least count\text{reading} = \text{main scale reading} + n \times \text{least count}

With the starting cylinder the zero has just passed 2.3 cm and line 6 lines up, so the diameter is 2.3+6×0.01=2.362.3 + 6 \times 0.01 = 2.36 cm.

Where the least count comes from

The ten vernier divisions fill only 9 mm, so each one is 0.9 mm long, a tenth of a millimetre shorter than a main-scale division. Open the jaw by 0.1 mm and the next line along slides onto a mark. That small difference, 0.1 mm or 0.01 cm, is the least count. A reading should always be written to that precision: 2.30 cm, not 2.3 cm, when line 0 lines up.

Zero error

Close an empty calliper and the two zeros should meet. A worn or bent jaw can leave the vernier zero a little to one side, and then every reading is off by the same amount.

  • Vernier zero to the right of 0. The calliper reads too much. If line 4 lines up, the error is 0.04 cm and you subtract it. Many courses call this a positive zero error.
  • Vernier zero to the left of 0. The calliper reads too little. Count the gap still to go: with line 7 in line, the error is (10 − 7) × 0.01 = 0.03 cm, which you add. This is a negative zero error.

In signed form both cases follow one rule: corrected reading = observed reading − zero error. The Punjab Class 9 book describes the same idea in words, as subtracting the error when the vernier zero sits on the right and adding it when it sits on the left. Pick your course with the symbol switcher to see its wording.

Outside and inside jaws

The large lower jaws grip the outside of an object, so they close until they touch it. The small upper jaws measure a hole: slip them inside and open them until they press on the wall. Both pairs share the same scales. The thin rod that slides out of the far end measures depths in the same way.

Practice mode

Practice gives you a random object and a calliper that may have a zero error. Press Check zero to close the empty jaws, read both scales, then type the true size. If your answer is wrong, the feedback names the likely slip, such as a forgotten zero error, a misread main scale or the wrong vernier line.

Check your understanding

8 questions

  1. 1.Ten vernier divisions together cover 9 mm of a main scale marked in millimetres. What is the least count?
  2. 2.The main scale reading is 4.1 cm and vernier line 7 lines up. The least count is 0.01 cm. What is the reading?
  3. 3.With the jaws closed, the vernier zero is to the right of the main-scale zero and line 2 lines up (least count 0.01 cm). The calliper then reads 3.48 cm on a rod. What is the rod's true diameter?
  4. 4.With the jaws closed, the vernier zero is to the left of the main-scale zero and line 6 lines up. The least count is 0.01 cm. How should each reading be corrected?
  5. 5.Which part of a vernier calliper measures the inner diameter of a pipe?
  6. 6.Why is a vernier calliper better than a metre rule for finding the diameter of a marble?
  7. 7.A student writes a calliper reading as 2.3 cm + 6 mm = 2.9 cm. What went wrong?
  8. 8.How do you find the main scale reading?

For teachers

Embed it in your site or open it full-screen for the projector.

Read more