Skip to content

Thermal physics simulation

Specific Heat Capacity Simulation

Run the classic specific heat capacity practical on a virtual bench. Heat a 1 kg sample, take joulemeter and thermometer readings, work out c from a graph, and find out exactly why energy lost to the room makes your answer too high.

Loading simulation…
Show symbols for

Predict first

Question 1 of 3

A 1 kg aluminium block and 1 kg of water in a beaker each get an identical 50 W heater, and both are lagged. After 10 minutes, how does the aluminium's temperature rise compare with the water's?

Try this

  1. 1Keep the starting set-up (aluminium block, Lagged, 50 W, 10 min timer) and press play. When the timer switches the heater off, keep your eye on the thermometer. Does the reading stop rising at that moment?
  2. 2Set Insulation to None and run the experiment again. Compare both values in the Results panel with the lagged run, then explain the change in one sentence.
  3. 3Choose Water under Heat a second sample beside it. Before you press play, predict how many times bigger the aluminium's temperature rise will be.
  4. 4Pick the Gradient (tangent) tool on the temperature–time graph and measure the straight part. Divide the heater power by the gradient (the mass is 1 kg) and compare the result with the Measured card.
  5. 5Choose Copper block and No losses. After the run, check that the final reading equals 20 °C plus the joulemeter reading divided by 390.

What happens on the bench

An immersion heater sits in a 1 kg sample: a beaker of water, a beaker of cooking oil, or a metal block with one hole for the heater and another for a thermometer probe. A small drop of oil in the probe hole gives good thermal contact. A joulemeter counts the energy going into the heater, a digital thermometer shows the temperature to 0.1 °C and a stopwatch runs alongside. One second on screen is twenty seconds of the experiment, so ten minutes of heating takes half a minute.

Press play, then press Record whenever you want a row in the results table. The simulation also notes the readings once a minute, unless you switch that off in the Results panel. Switch the heater off and on yourself, or let the timer do it.

Two ways to get c from your readings

The quick method uses just two readings, the first one and the highest one:

c=ΔEm Δθc = \frac{\Delta E}{m\,\Delta\theta}

Take the energy from the joulemeter and the temperature rise from the thermometer. For the rise, use the highest reading, which comes a little after the heater goes off.

The more reliable method uses a graph. Plot temperature against energy supplied. In the straight part, each joule raises the temperature by 1/(mc)1/(mc), so the gradient equals 1/(mc)1/(mc) and c=1/(m×gradient)c = 1/(m \times \text{gradient}). A line through many points smooths out the small rounding in each reading. The simulation leaves out readings from the first minute, while the block is still evening out, and readings taken with the heater off.

Why your answer comes out too high

With the starting settings you should find a value close to 930 J/(kg °C), slightly above the accepted 900. Remove the lagging and it rises above 1000. The reason is worth learning properly. The joulemeter measures every joule the heater supplies, yet some of that energy warms the air, the bench and the mat instead of the block. That energy never appears as a temperature rise. The rise is therefore smaller than it would be, and dividing the energy by a smaller rise gives a bigger value of c.

The loss rate in the model grows with how far the sample is above room temperature. That is why the temperature–time graph bends over more and more as the block gets hotter, and why lagging, which slows the losses, straightens it. The green line on the graph shows where the temperature would be if nothing escaped. The bar under the readouts splits the supplied energy into the part stored in the sample and the part lost to the room. The two parts always add up to the joulemeter total, because no energy is created or destroyed.

Comparing materials

Heat a second sample beside the first with an identical heater. Equal masses and equal energy give very different rises. Copper warms more than twice as much as aluminium, and water warms least of all. Notice the sizes too: 1 kg of copper is a much smaller block than 1 kg of aluminium, because copper is far denser.

Choose No losses to see the ideal case that no real lab reaches. The final reading then matches 20 ∘C+E/(mc)20\ ^\circ\text{C} + E/(mc) exactly. For the energy and power side of this practical, the power and efficiency simulation is a good next step.

Equations

  • Power and energy transferred

    P=Et

    power = energy transferred ÷ time

    Open calculator →
  • Specific heat capacity

    ΔE=mcΔθ

    change in thermal energy = mass × specific heat capacity × temperature change

    Open calculator →

Check your understanding

8 questions

  1. 1.Aluminium has a specific heat capacity of about 900 J/(kg °C). What does this tell you?
  2. 2.A 50 W immersion heater is switched on for 4 minutes. How much energy does it supply?
  3. 3.A 1 kg copper block (c = 390 J/(kg °C)) takes in 7800 J with no losses. By how much does its temperature rise?
  4. 4.Students heating an unlagged block usually get a value of c that is larger than the accepted one. Why?
  5. 5.What is the main reason for wrapping the block in insulation?
  6. 6.A graph of temperature against energy supplied for a 1 kg block has a gradient of 0.0011 °C/J. What value of c does this give?
  7. 7.After the heater is switched off, the thermometer reading rises a little more before it starts to fall. What causes this?
  8. 8.1 kg of water and 1 kg of cooking oil are heated by identical heaters. Which one warms faster, and why?

For teachers

Embed it in your site or open it full-screen for the projector.

Read more