Skip to content

Forces simulation

Impulse and Car Safety Simulation

Drive a car into a concrete barrier and watch a crash-test dummy inside. Switch the crumple zone, seat belt and airbag on and off, then compare stopping times, forces and the area under each force–time graph.

Loading simulation…
Show symbols for

Predict first

Question 1 of 4

A 1000 kg car hits the barrier at 15 m/s, once with a stiff front and once with a crumple zone. How does the car's change in momentum compare in the two crashes?

Try this

  1. 1Start with the default set-up, Modern car: everything on, and press play. Then choose No safety features from the Set-up menu and crash again. Compare the peak force on the dummy in the two runs.
  2. 2Crash once with the Crumple zone on and once with it off, keeping everything else the same. After each crash, use the area tool on the Force on the car graph. Does the shaded area change, or only the shape of the curve?
  3. 3Choose Crumple zone, no seat belt. Before you press play, decide whether the dummy starts to slow down at the same moment as the car. Check your answer on the Force on the dummy graph.
  4. 4Note the average force on the car at 15 m/s and predict its value at 30 m/s. Then move Speed before the crash to 30 m/s and check the readout. The crush distance stays the same, so why is the force more than double?
  5. 5Choose Crumple zone and seat belt, press Slow-mo, then press play and watch the seat belt tighten as the car hits the barrier. Then switch the Seat belt off, press play again and see how far the dummy travels before anything slows it down.

What happens in the crash

A car drives into a solid concrete barrier and stops. A crash-test dummy sits in the driving seat, and the side of the car is cut away so you can watch the dummy, the seat belt and the airbag during the impact. The whole event lasts about a tenth of a second, so it plays many times slower than real life. Live meters show the force on the car and on the dummy, and the table gives each one's stopping time, average and peak force, and deceleration.

The change in momentum is fixed

Before the crash the car has momentum p=mvp = mv. Afterwards it is at rest. However the stop happens, the momentum has to fall by exactly that amount, so no safety feature can change Δp\Delta p. What a feature can change is how quickly the momentum disappears. The average force equals the change in momentum divided by the time it takes,

F=ΔpΔtF = \frac{\Delta p}{\Delta t}

so spreading the same change over a longer time Δt\Delta t gives a smaller average force. The readouts show this at once: with the crumple zone, the car's stopping time is five times as long as with a stiff front, and its average force is one fifth as big.

Reading the force–time graphs

Each graph plots the size of a force against the time since impact. The shaded area under a curve is the impulse, FΔtF\Delta t, which equals the change in momentum. Choose the area tool and drag across the whole curve to measure it in newton seconds. It matches Δp\Delta p in kilogram metres per second, because those two units are identical. Your previous crash stays on the graph for comparison, along with the same crash with no safety features. Without the features you get a tall, thin spike; with them, a lower and wider hump. The areas are equal.

Belts, airbags and the dummy

A belted dummy is held to the seat from the first instant, so it slows down with the car and then a little more while the belt stretches. Without a belt nothing pushes on the dummy at first. It carries on at the original speed until its chest meets the steering wheel, which stops it very abruptly. On the dummy's graph, the force does not even start until the car has nearly or completely stopped. An airbag gives an unbelted dummy something softer to sink into, but it is the belt that lets the dummy share the car's longer stop.

How the model works

The numbers come from a simple model, set out under the graphs. After touching the barrier the car travels a fixed crush distance: 0.10 m with a stiff front and 0.50 m with a crumple zone. The force on the car, and on a belted dummy, rises steadily, levels off and falls again in a symmetric pattern. So the average speed during the stop is half the starting speed, which gives a stopping time of Δt=2×crush distance÷starting speed\Delta t = 2 \times \text{crush distance} \div \text{starting speed}. Because the crush distance in this model does not depend on speed (a real car crushes further in a faster crash), doubling the speed doubles Δp\Delta p but halves Δt\Delta t, so the average force becomes four times as large. Real crashes are messier. The simulation shows how stopping time affects force; it does not tell you how likely an injury is.

Is this on my course?

AQA GCSE Physics covers this in section 4.5.7.3, Changes in momentum. It appears only in the separate physics course, not in Combined Science, and it is Higher tier, as is everything in section 4.5.7. You are given F=mΔv/ΔtF = m\Delta v / \Delta t on the equation sheet and should be able to use it to explain how safety features such as seat belts and air bags work. For Cambridge IGCSE Physics (0625), topic 1.6 lists momentum, impulse and F=Δp/ΔtF = \Delta p / \Delta t as Supplement material, which is assessed only on the Extended papers. Neither syllabus mentions force–time graphs, and AQA does not use the word impulse, so treat the area under the graph as a useful extra that follows from the same equation.

Equations

Check your understanding

7 questions

  1. 1.A 1200 kg car moving at 10 m/s hits a wall and comes to rest. How much momentum does it lose?
  2. 2.In a crash, a car's momentum changes by 18 000 kg m/s in 0.12 s. What is the average force on the car?
  3. 3.How does a crumple zone reduce the force on a car in a collision?
  4. 4.What does the area under a force–time graph for a crash represent?
  5. 5.In the simulation, why does an unbelted dummy feel a far larger force than a belted one?
  6. 6.An airbag stops a 70 kg passenger moving at 14 m/s in 0.098 s. What is the average force on the passenger?
  7. 7.A crumple zone always crushes by the same distance. If the car hits the barrier at twice the speed, what happens to the stopping time?

For teachers

Embed it in your site or open it full-screen for the projector.

Read more