Skip to content

Punjab Board Class 9 Physics · Physical quantities and measurements

Measuring cylinders and displacement cans

Section 1.8

Liquids and irregular solids are measured in a measuring cylinder (1 mL = 1 cm³). Keep your eye level with the meniscus: read its bottom for water, its top for mercury. A sinking solid has volume V₂ − V₁. A solid too wide for the cylinder goes in a displacement can; the overflow equals its volume.

Loading simulation…

Symbols match your course. Open the full measuring density simulation for more presets and teacher tools.

Volume and its units

The volume of a body is the space it occupies. Its SI unit is the cubic metre (m³), which is far too big for laboratory work, so we usually use cubic centimetres (cm³, also written cc) or millilitres (mL).

1 mL=1 cm31 L=1000 cm31 m3=106 cm31\ \text{mL} = 1\ \text{cm}^3 \qquad 1\ \text{L} = 1000\ \text{cm}^3 \qquad 1\ \text{m}^3 = 10^6\ \text{cm}^3

A regular solid, such as a brick, has a volume you can calculate from its measured sides. Liquids and irregular solids need a measuring cylinder.

The measuring cylinder

A measuring cylinder is a tall, narrow, see-through vessel with a volume scale running up its side, usually in cm³ or mL. Before reading one, work out what a single small division is worth. If the gap between the 20 and 30 marks holds ten small divisions, each one is 1 cm³.

Reading the meniscus without parallax

In a narrow tube, the surface of a liquid is not flat. This curved surface is called the meniscus.

  • Water (and most liquids) curves downwards in the middle, a concave surface. Read the scale level with the bottom of the curve.
  • Mercury bulges upwards, a convex surface. Read level with its top.

Stand the cylinder on a level table and bend down until your eye is level with the liquid surface. Looking down from above makes the reading too high; looking up from below makes it too low. This mistake is a parallax error.

Volume of an irregular solid by displacement

A stone or a padlock has no formula for its volume. A solid that sinks pushes aside, or displaces, its own volume of liquid.

  1. Pour enough liquid into the cylinder to cover the solid completely, and note the reading V1V_1.
  2. Tie the solid to a thread and lower it gently, so no liquid splashes out and the glass does not crack.
  3. Note the new reading V2V_2. The volume of the solid is
V=V2−V1V = V_2 - V_1

If the solid dissolves in water, use a liquid it does not dissolve in. A lump of rock salt from the Khewra mine, for example, can be measured in kerosene oil instead.

The displacement (overflow) can

Some solids are too wide for a measuring cylinder. Use a displacement can instead: a wide can with a spout near its top.

  1. Stand the can on a level table. Pour in water until some runs out of the spout, then wait for the last drips to fall.
  2. Put an empty measuring cylinder (or a beaker) under the spout.
  3. Lower the solid gently on a thread until it is completely under water.
  4. The overflow has the same volume as the solid. Water caught in a beaker is poured into a measuring cylinder to read it.

Worked numerical 1: a stone

A measuring cylinder holds 35 cm³ of water. When a stone is lowered in, the reading rises to 47 cm³. Find the volume of the stone in cm³ and in m³.

V=V2−V1=47 cm3−35 cm3=12 cm3V = V_2 - V_1 = 47\ \text{cm}^3 - 35\ \text{cm}^3 = 12\ \text{cm}^3 V=12×10−6 m3=1.2×10−5 m3V = 12 \times 10^{-6}\ \text{m}^3 = 1.2 \times 10^{-5}\ \text{m}^3

Worked numerical 2: twenty ball bearings

One small ball bearing barely changes the reading, so twenty identical ones are dropped in together. The water level rises from 40.0 cm³ to 46.0 cm³.

Volume of 20 balls=46.0−40.0=6.0 cm3\text{Volume of 20 balls} = 46.0 - 40.0 = 6.0\ \text{cm}^3 Volume of one ball=6.0 cm320=0.30 cm3\text{Volume of one ball} = \frac{6.0\ \text{cm}^3}{20} = 0.30\ \text{cm}^3

Using the simulation

In the simulation above, press Irregular, the second experiment button under the stage. A Pebble sits on the balance beside a measuring cylinder holding 50 cm³ of water (Water at the start). Press Lower in: the pebble sinks, the Reading after card shows 58 cm³, and the Volume card shows the rise, 8 cm³ (58 − 50). The round magnifier beside the cylinder shows the bottom of the meniscus close up, which is where you read.

  1. Choose Large brass key from Object, drag Water at the start down to 10 cm³ and press Lower in. Part of the key stays above the water, and a warning says the reading rose by less than its volume. Raise the water to 50 cm³ and press Lower in again: the volume is now 3 cm³.
  2. Choose Large stone. It is too wide for the measuring cylinder, so pick Displacement can under Volume by displacement and press Lower in. Water runs from the spout into a measuring cylinder, and the Water collected card settles at 45 cm³.
  3. Press Liquid (the third experiment button), then Pour to put 50 cm³ of cooking oil into the cylinder. Read the bottom of the meniscus in the magnifier yourself.

Common mistakes

  • Reading the edge where water climbs up the glass. For water, read level with the bottom of the meniscus; only mercury is read at the top.
  • Reading with the eye above or below the liquid surface. This parallax error makes the reading too high from above and too low from below.
  • Writing V₂ as the volume of the solid. The volume is the rise in the reading, V₂ − V₁.
  • Starting with too little water, so part of the solid stays above the surface and the rise is smaller than its volume.
  • Lowering the solid into a displacement can that is not filled right up to the spout. Some displaced water then stays in the can and the volume comes out too small.
  • Converting cm³ to m³ by dividing by 100 or 1000. 1 m³ = 10⁶ cm³, so divide by 1 000 000.

Exam-style questions

Original questions written in the style of Punjab board exams. Try each one before you reveal the answer.

  1. 1.A student uses a measuring cylinder to measure the volume of some water.

    1. (a)What is meant by the meniscus?

      1 mark
      Show the answer

      Answer: The curved surface of a liquid in a narrow tube or cylinder.

      Marking points

      • Curved surface of the liquid in the cylinder
    2. (b)Where should the scale be read for (i) water, (ii) mercury?

      2 marks
      Show the answer

      Answer: (i) Water: level with the bottom of the concave meniscus. (ii) Mercury: level with the top of the convex meniscus.

      Marking points

      • Water: bottom of the meniscus
      • Mercury: top of the meniscus
    3. (c)The student reads the scale while looking down at the surface from above. Name the error made and state whether the reading is too high or too low.

      2 marks
      Show the answer

      Answer: Parallax error. Looking down from above makes the reading too high.

      Marking points

      • Parallax error
      • Reading too high
  2. 2.A measuring cylinder contains 52 cm³ of water. A metal bolt is tied to a thread and lowered into the water until it is completely covered. The reading rises to 61 cm³.

    1. (a)Calculate the volume of the bolt in cm³.

      2 marks
      Show the answer

      Answer: V = V₂ − V₁ = 61 cm³ − 52 cm³ = 9 cm³.

      Marking points

      • V = V₂ − V₁ = 61 − 52
      • 9 cm³
    2. (b)Express this volume in m³.

      1 mark
      Show the answer

      Answer: 9 cm³ = 9 × 10⁻⁶ m³.

      Marking points

      • 9 × 10⁻⁶ m³
    3. (c)Why is the bolt lowered on a thread instead of being dropped in?

      1 mark
      Show the answer

      Answer: So that no water splashes out (which would make the reading too small) and the bolt does not crack the cylinder.

      Marking points

      • Prevents splashing (lost water) / prevents breaking the cylinder
  3. 3.A large stone is too wide to go into any measuring cylinder in the laboratory.

    1. (a)Name the apparatus used to find its volume.

      1 mark
      Show the answer

      Answer: A displacement can (overflow can), with a measuring cylinder.

      Marking points

      • Displacement can / overflow can
    2. (b)Describe how this apparatus is used to find the volume of the stone.

      4 marks
      Show the answer

      Answer: Stand the can on a level table and pour in water until some runs out of the spout; wait for the dripping to stop. Put an empty measuring cylinder (or beaker) under the spout. Lower the stone gently on a thread until it is completely under water. The water that overflows, read on the measuring cylinder, has the same volume as the stone.

      Marking points

      • Can filled until water runs from the spout; dripping allowed to stop
      • Empty measuring cylinder or beaker placed under the spout
      • Stone lowered gently (on a thread) until fully under water
      • Volume of overflow collected = volume of the stone
  4. 4.Fifty identical small steel nails are dropped together into a measuring cylinder of water. The reading rises from 20.0 cm³ to 22.5 cm³.

    1. (a)Calculate the volume of one nail.

      2 marks
      Show the answer

      Answer: Volume of 50 nails = 22.5 − 20.0 = 2.5 cm³. Volume of one nail = 2.5 cm³ ÷ 50 = 0.050 cm³.

      Marking points

      • Volume of 50 nails = 2.5 cm³
      • 2.5 ÷ 50 = 0.050 cm³
    2. (b)Why are fifty nails used instead of one?

      1 mark
      Show the answer

      Answer: One pin would raise the level by much less than one division, too little to read. Fifty pins give a readable rise, and dividing shares the reading error among them.

      Marking points

      • One pin's rise is too small to read accurately

Quick check

6 questions

  1. 1.One millilitre (1 mL) is equal to:
  2. 2.For water in a measuring cylinder, the reading should be taken at:
  3. 3.The water in a measuring cylinder rises from 30 cm³ to 38 cm³ when a stone is lowered in. The volume of the stone is:
  4. 4.A displacement can is used to find the volume of a solid that:
  5. 5.A student reads a measuring cylinder with the eye above the level of the liquid surface. The reading is:
  6. 6.The surface of mercury in a glass tube is: