What AQA asks for: spec point 4.3.1.1
Density is on both tiers, in GCSE Physics and in Combined Science. Its equation is not on the equation sheet, so you must remember it. You should be able to:
- recall and use , including changes of state, where mass is conserved
- use the particle model to explain why solids, liquids and gases have different densities, and draw simple particle diagrams
- describe Required practical 5: the density of regular solids, irregular solids and liquids. Combined Science students do the same practical under a different number.
The equation
Density (rho) is in kilograms per metre cubed (kg/m³), mass in kg and volume in m³. Lab readings in g and cm³ give g/cm³; multiply by 1000 to convert, since 1 g/cm³ = 1000 kg/m³. So aluminium at 2.7 g/cm³ is 2700 kg/m³.
Worked example 1: a pebble. A dry pebble has a mass of 39 g. Lowered into a measuring cylinder, it raises the water level from 42 cm³ to 57 cm³.
Given: g kg, cm³ m³. Equation: . Substitution: . Answer: kg/m³, which is 2.6 g/cm³.
Worked example 2: air in a classroom. A classroom measures 8.0 m × 6.0 m × 3.0 m, and air has a density of about 1.2 kg/m³. Estimate the mass of air inside.
Given: m³, kg/m³. Equation: rearrange to . Substitution: . Answer: about 170 kg (2 s.f.).
Particles and density
- Solid: particles packed tightly in a regular pattern, vibrating about fixed positions.
- Liquid: particles still touching, but randomly arranged and able to slide past one another.
- Gas: particles far apart, moving quickly in random directions.
Close-packed particles put a lot of mass into each cubic metre, so solids and liquids are dense. A gas spreads its particles through a far larger volume: liquid water is close to 1000 kg/m³, but steam at 100 °C is under 1 kg/m³.
Mass is conserved in a change of state, so a change in volume changes the density. Most substances are slightly denser as solids, but water expands as it freezes, so ice (about 920 kg/m³) floats.
Required practical 5
Regular solid. Measure its sides with a ruler (Vernier callipers or a micrometer for small objects), calculate the volume and find the mass on a top-pan balance.
Irregular solid. Find the mass while the object is dry, then find its volume by displacement:
- Part-fill a measuring cylinder and read the volume. Lower the object in on a thread until it is fully under, then read again. The difference is the object's volume.
- If it is too wide for the cylinder, fill a eureka can until water runs from the spout. Once it stops dripping, put an empty measuring cylinder under the spout and lower the object in; the water collected has the object's volume.
Liquid. Stand an empty measuring cylinder on the balance and zero it, or record its mass. Pour in some liquid, then read its volume and its mass.
Read volumes at the bottom of the meniscus, with your eye level with it, and repeat each measurement.
Using the simulation
In the simulation above, the Regular experiment starts with a 2.0 cm Aluminium cube. The Volume card reads 8.00 cm³, but Mass says Press Weigh. Press Weigh it: the balance shows 21.6 g and Density gives 2.70 g/cm³ = 2700 kg/m³. Pick Copper from Material while the cube is on the balance: 71.2 g and 8.90 g/cm³.
Switch to Irregular. The pebble sits on the balance (20.8 g) beside 50 cm³ of water in a measuring cylinder. Press Lower in and the reading climbs to 58 cm³, so the volume is 8 cm³ and the density 2.60 g/cm³. Now choose Large stone from Object: it will not fit, so select Eureka can.
Under Liquid, press Pour to add 50 cm³ of cooking oil. The mass by difference is 150.3 g − 104.3 g = 46.0 g, giving 0.920 g/cm³. Switching on Zero the balance with the empty cylinder on it does that subtraction for you.