What this topic covers
At Vostok research station in Antarctica, the air once fell to about −89 °C, and laboratories cool materials far below that. Yet there is a floor that nothing can go beneath. This topic (syllabus 2.1.2–2.1.3) explains it and the kelvin scale built on it.
Temperature and moving particles (Core)
The particles of every substance are always on the move. In a solid they vibrate about fixed positions; in a liquid or a gas they also travel from place to place.
Raise the temperature and the particles move faster on average. Lower it and they slow down. (Supplement, from topic 2.2.2: a rise in temperature is a rise in the average kinetic energy of the particles.) Particles do not stop at 0 °C: air molecules at the freezing point of water still rush about at hundreds of metres per second.
Absolute zero (Core)
Keep cooling a substance and its particles keep slowing, but not without limit. At −273 °C their kinetic energy is as small as it can ever become, so no lower temperature is possible. This is absolute zero. Laboratories get extremely close to it but never all the way.
The kelvin scale (Core)
The kelvin scale starts at absolute zero, 0 K. Each kelvin is the same size as one degree Celsius, so converting only means shifting by 273:
Write the unit as K, with no degree sign; a kelvin temperature is never negative. Because the steps match, a change in temperature has the same number on both scales: a rise of 30 °C is a rise of 30 K.
| Example | °C | K |
|---|---|---|
| Pure water boiling (standard atmospheric pressure) | 100 | 373 |
| A very hot afternoon in Karachi | 40 | 313 |
| Pure water freezing | 0 | 273 |
| Lowest air temperature recorded at a weather station (Vostok) | about −89 | about 184 |
| Absolute zero | −273 | 0 |
How a gas points to absolute zero (beyond the syllabus)
Seal a fixed mass of gas in a rigid container and measure its pressure at several temperatures. As the gas cools, its particles slow down and strike the walls less often and less hard, so the pressure falls along a straight line. Extended to colder temperatures, the line reaches zero pressure at about −273 °C, whichever gas you use. A real gas turns into a liquid long before then, so the line must be extended rather than measured. Against kelvin temperature, the same line passes through the origin.
Worked example: converting temperatures (Core)
(a) Liquid oxygen boils at 90 K. Give this in °C.
(b) A pizza oven in Naples runs at about 450 °C. Give this in kelvin.
(c) Water in a pan warms from 15 °C to 85 °C. Find the rise in kelvin.
Answer: 70 K, the same number as the 70 °C rise. Never add 273 to a difference.
Simulation tasks
In the simulation above, choose Constant volume from the Experiment menu. The piston stays at 300 cm³, and the Set temperature slider works in kelvin, with the Celsius value beneath it.
- (Core) Press Play. The Temperature card reads 300 K with 27 °C under it: check that 27 + 273 = 300.
- (Core) Press Heat three times, to 450 K. The particles' colours shift towards the fast end of the Particle speed key, the Average kinetic energy under Working goes from about 6.21 × 10⁻²¹ J to about 9.32 × 10⁻²¹ J, and the pressure settles at about 152 kPa.
- (Extra, beyond the syllabus) Use Heat and Cool to visit five or six temperatures from 100 K to 600 K, pressing Record each time the reading settles. With p against °C chosen under Plot, the note under the graph says where the best-fit line reaches zero pressure: near −273 °C, shifted a little by the wobbling readings. p against K gives a value near 0 K.
- (Extension) The Pressure ÷ temperature card stays near 0.34 kPa/K.
The slider stops at 100 K (−173 °C), so here too absolute zero is found only by extending the line.