Skip to content

GCSE Physics — AQA · Working scientifically

Measuring instruments

AT 1WS 2.6

Choose and read instruments for AQA required practicals. Resolution is the smallest change an instrument can show: 1 mm for a ruler, 0.1 mm for Vernier callipers, 0.01 mm for a micrometer. Correct zero errors, and quote a mean with half the range as its uncertainty. Both tiers.

Loading simulation…

Symbols match your course. Open the full vernier caliper simulation for more presets and teacher tools.

What AQA expects (AT 1 and WS 2.6)

Measuring skills are assessed on both tiers, in GCSE Physics and in Combined Science. There is no equation to learn. Questions built around the required practicals expect you to:

  • pick suitable apparatus for a measurement and justify your choice
  • read a scale and record the value properly, with its unit
  • judge results in terms of accuracy, precision and error, and use repeat readings to estimate an uncertainty.

For Required practical 5 on density (Combined Science numbers it differently), the specification gives a ruler, a micrometer or Vernier callipers as examples of apparatus for measuring an object's sizes. It names these instruments but does not describe their scales, so reading a vernier is useful practice rather than a listed requirement.

Resolution

The resolution of an instrument is the smallest change in the quantity being measured that makes its reading change. Exam questions often ask for it. A digital balance that shows 34.27 g has a resolution of 0.01 g.

InstrumentUsual resolutionSensible job
Ruler or metre rule1 mma block a few centimetres long
Vernier callipers0.1 mm (0.01 cm)a coin, a marble or a short rod
Micrometer0.01 mma wire or a sheet of card

Choose a resolution that is tiny compared with the length itself. Being 1 mm out hardly matters on a 30 cm plank, but it is half of a 2 mm wire.

Reading Vernier callipers

Close the jaws gently on the object. Find the zero on the sliding vernier scale and note the last millimetre mark on the main scale that it has passed: the main scale reading. Then find the one vernier line that sits exactly on a main-scale mark. Each vernier division adds 0.1 mm.

Worked example 1: a steel ball bearing. The vernier zero has passed the 1.7 cm mark, and vernier line 4 lines up.

Given: main scale reading =1.7= 1.7 cm, line 4, each division =0.01= 0.01 cm. Working: 1.7+4×0.011.7 + 4 \times 0.01. Answer: 1.741.74 cm. Always record to 0.01 cm: if line 0 had lined up, the reading would be 1.70 cm, not 1.7 cm.

With the jaws closed on nothing, these callipers show +0.03 cm instead of zero. This zero error adds the same amount to every reading, so it is a systematic error. Corrected reading = observed reading − zero error =1.74−0.03=1.71= 1.74 - 0.03 = 1.71 cm. A negative zero error is therefore added on.

Accuracy, precision and uncertainty

  • A measurement is accurate when it is close to the true value.
  • Measurements are precise when repeat readings cluster tightly together.
  • Random errors scatter readings unpredictably. Take several readings and work out a mean.
  • Systematic errors, such as a zero error, shift every reading by the same amount. Repeating cannot remove them; find the cause and correct for it.

So an uncorrected zero error can give readings that are precise yet inaccurate.

Worked example 2: mean and uncertainty. A student measures the diameter of a marble five times: 1.62 cm, 1.66 cm, 1.64 cm, 1.63 cm and 1.65 cm.

Mean: 8.205=1.64\dfrac{8.20}{5} = 1.64 cm. Range: 1.66−1.62=0.041.66 - 1.62 = 0.04 cm. Uncertainty: half the range, ±0.02\pm 0.02 cm. Result: 1.64±0.021.64 \pm 0.02 cm.

Using the simulation

In the simulation above, the outside jaws start closed on the Brass cylinder. The Main scale reading card shows 2.3 cm, Vernier division in line shows 6 and Least count shows 0.01 cm. Least count is the smallest step this scale can show, so here it is the resolution. The Reading card gives 2.36 cm, or 23.6 mm if you choose mm under Show lengths in.

Press Positive under Zero error. Its size starts at 0.03 cm, so Observed reading jumps to 2.39 cm while Corrected reading stays at 2.36 cm. Try Negative and watch the observed value drop below the true one.

Then choose Practice under Mode. Press Check zero to read any zero error, press Back, type the true size and press Check. New sets another task.

For very thin objects, open the micrometer screw gauge simulation, which reads to 0.01 mm.

Common mistakes

  • Dropping a zero that matters. A calliper reading of 2.30 cm must not be written as 2.3 cm, because the instrument resolves 0.01 cm.
  • Taking the main scale reading from the mark beside the vernier line that lines up. The main scale reading is the last millimetre mark the vernier zero has passed.
  • Adding the vernier line number as whole millimetres. If line 6 lines up, it adds 6 × 0.1 mm = 0.6 mm, not 6 mm.
  • Correcting a zero error the wrong way. Corrected reading = observed reading − zero error, so a positive zero error is taken away and a negative one is added on.
  • Mixing up accuracy and precision. Precise readings agree closely with each other; accurate readings are close to the true value. A zero error can make readings precise but inaccurate.
  • Thinking repeat readings cancel a systematic error. A mean reduces the effect of random error only; a systematic error must be found and corrected.

Exam-style questions

Original questions written in the style of GCSE AQA. Try each one before you reveal the answer.

  1. 1.A student wants to find the density of a small steel ball bearing. Its diameter is roughly 6 mm. The student can use a 30 cm ruler marked in millimetres, a set of Vernier callipers or a micrometer.

    1. (a)Give the resolution of the ruler.

      1 mark
      Show the answer

      Answer: 1 mm

      Marking points

      • 1 mm (accept 0.1 cm)
    2. (b)Which instrument should the student use to measure the diameter of the ball bearing? Give a reason for your answer.

      2 marks
      Show the answer

      Answer: The micrometer, because it has the smallest resolution (0.01 mm), which is very small compared with a 6 mm diameter.

      Marking points

      • Micrometer (allow Vernier callipers).
      • Its resolution is small compared with the 6 mm diameter (micrometer 0.01 mm, the smallest; callipers 0.1 mm), whereas the ruler's 1 mm is a large fraction of 6 mm.
    3. (c)The student measures the diameter five times. The readings are 6.32 mm, 6.35 mm, 6.33 mm, 6.36 mm and 6.34 mm. Calculate the mean diameter.

      2 marks
      Show the answer

      Answer: mean = (6.32 + 6.35 + 6.33 + 6.36 + 6.34) ÷ 5 = 31.70 ÷ 5 = 6.34 mm

      Marking points

      • Sum of the readings ÷ 5 (31.70 ÷ 5)
      • 6.34 mm
    4. (d)Use the readings to estimate the uncertainty in the mean diameter.

      2 marks
      Show the answer

      Answer: Range = 6.36 − 6.32 = 0.04 mm. Uncertainty = half the range = ± 0.02 mm.

      Marking points

      • Range = 6.36 − 6.32 = 0.04 mm
      • Uncertainty = ± 0.02 mm (half the range)
  2. 2.A technician uses Vernier callipers to measure the outside diameter of a plastic pipe. The main scale is marked in millimetres. Each division on the vernier scale is worth 0.1 mm.

    1. (a)The vernier zero is just past the 32 mm mark on the main scale, and vernier line 7 lines up with a main-scale mark. Give the reading on the callipers.

      2 marks
      Show the answer

      Answer: 32 mm + 7 × 0.1 mm = 32.7 mm

      Marking points

      • 32 + 7 × 0.1
      • 32.7 mm
    2. (b)With the jaws closed and nothing between them, the callipers read 0.2 mm. Name this type of error.

      1 mark
      Show the answer

      Answer: A zero error, which is a type of systematic error.

      Marking points

      • Zero error / systematic error
    3. (c)Calculate the true diameter of the pipe.

      2 marks
      Show the answer

      Answer: true diameter = 32.7 − 0.2 = 32.5 mm

      Marking points

      • 32.7 − 0.2 (allow their reading from the first part)
      • 32.5 mm
    4. (d)Explain why measuring the pipe several more times and calculating a mean would not remove this error.

      2 marks
      Show the answer

      Answer: The zero error makes every reading too large by the same amount, 0.2 mm. The mean of readings that are all 0.2 mm too large is also 0.2 mm too large; averaging only reduces random error.

      Marking points

      • The error shifts every reading by the same amount in the same direction.
      • So the mean is shifted by the same amount (a mean only reduces the effect of random errors).
  3. 3.Two students each measure the thickness of the same coin four times with their own micrometer. The true thickness of the coin is 1.85 mm. Student A records 1.84 mm, 1.86 mm, 1.85 mm and 1.85 mm. Student B records 1.95 mm, 1.96 mm, 1.95 mm and 1.96 mm.

    1. (a)Give the resolution of the micrometers used.

      1 mark
      Show the answer

      Answer: 0.01 mm

      Marking points

      • 0.01 mm
    2. (b)Which student's readings are more accurate? Give a reason for your answer.

      2 marks
      Show the answer

      Answer: Student A. The mean of A's readings is 1.85 mm, the same as the true value, while B's mean (about 1.96 mm) is about 0.1 mm too large.

      Marking points

      • Student A
      • A's readings (mean 1.85 mm) are closer to the true value.
    3. (c)A teacher says that Student B's readings are precise. Explain what this means.

      1 mark
      Show the answer

      Answer: The repeat readings are very close to each other: they spread over only 0.01 mm.

      Marking points

      • The readings are close together / cluster closely (range only 0.01 mm).
    4. (d)Suggest the most likely cause of the error in Student B's readings, and how Student B could correct the results.

      2 marks
      Show the answer

      Answer: Student B's micrometer probably has a zero error of about +0.10 mm. B should close the micrometer with nothing in it, read the zero error, and subtract it from every reading.

      Marking points

      • A zero error (systematic error) in Student B's micrometer.
      • Close the micrometer with nothing between the jaws, read the zero error and subtract it from each reading.

Quick check

6 questions

  1. 1.What is the resolution of a ruler marked in millimetres?
  2. 2.On a set of Vernier callipers, the vernier zero has just passed 4.2 cm and vernier line 5 lines up. Each vernier division is worth 0.01 cm. What is the reading?
  3. 3.Which instrument is best for measuring the diameter of a thin copper wire?
  4. 4.Four readings of a length are 25.2 mm, 25.6 mm, 25.4 mm and 25.4 mm. What is the uncertainty in the mean?
  5. 5.A balance shows 0.4 g with nothing on its pan. What kind of error will this cause in every mass measured on it?
  6. 6.A set of repeat readings are very close together but all far from the true value. How should they be described?