What Vernier Callipers are for
A metre rule cannot tell whether a marble is 1.6 cm or 1.65 cm wide, because it only reads to the nearest millimetre. Vernier Callipers read ten times more finely, to 0.1 mm, for lengths up to about 15 cm: the outer diameter of a pipe, the inside width of a bottle neck or the depth of a small tin.
| Part | What it does |
|---|---|
| Main scale | Fixed scale along the beam, marked in millimetres |
| Vernier scale | Short sliding scale: 10 equal divisions spread over 9 mm |
| Outside jaws | Grip an object from outside, for an external diameter, width or thickness |
| Inside jaws | Open inside a hole or tube, for an internal diameter |
| Tail (depth gauge) | Strip that slides out of the far end, for the depth of a hollow object |
Least count
The least count (L.C.) is the smallest length an instrument can measure reliably. Each Vernier division is 9 mm ÷ 10 = 0.9 mm long, which is exactly 0.1 mm shorter than one main-scale division. So
Sharing one main-scale division among all ten Vernier divisions gives the same value: .
Taking a reading
- Main scale reading (M.S.R.): find the Vernier zero and note the last main-scale mark it has passed.
- Vernier scale reading (V.S.R.): look along the Vernier scale for the one division that sits exactly in line with a main-scale mark. Its number is the V.S.R.
- Put them together:
Because the least count is 0.01 cm, give every result to two decimal places in centimetres. If division 0 is in line, write 3.20 cm, not 3.2 cm.
Zero error and the corrected reading
Before measuring, close the jaws gently and compare the two zeros. If they coincide, there is no zero error. If not, every reading is wrong by the same amount, the zero error, and each observed reading must be corrected.
- Vernier zero on the right of the main-scale zero. The instrument reads more than the true length. With division in line, zero error , and you subtract it.
- Vernier zero on the left of the main-scale zero. The instrument reads less than the true length. Count the divisions still missing: zero error , and you add it.
Worked numerical: a copper pipe and a marble
(a) With the jaws closed, the Vernier zero lies on the right of the main-scale zero and division 2 is in line. On a copper pipe the M.S.R. is 2.4 cm and division 7 is in line. Find the pipe's outer diameter.
(b) A second instrument, closed, has its Vernier zero on the left of the main-scale zero with division 7 in line. On a glass marble it gives an M.S.R. of 1.5 cm with division 2 in line.
Using the simulation
In the simulation above, the outside jaws are closed on a Brass cylinder. The Main scale reading card shows 2.3 cm, the Vernier scale reading (division in line) card shows 6, and the working line gives 2.3 cm + 6 × 0.01 cm = 2.36 cm. In the magnified view, division 6 glows where it meets a main-scale mark.
- Press the single › arrow (Open the jaws by 0.1 mm) a few times. Each press moves the glow one division along and adds 0.01 cm. Press Close to grip the cylinder again.
- Under Zero error, choose Right of 0. The Observed reading becomes 2.39 cm, the Zero error card shows 0.03 cm with "Vernier zero on the right: subtract", and the Corrected reading stays 2.36 cm. Choose Left of 0: the observed reading falls to 2.33 cm and the error is added.
- Pick Nothing (jaws empty) from In the jaws and press Close. With Left of 0 still chosen, division 7 is in line and the working shows (10 − 7) × 0.01 cm = 0.03 cm.
- Choose Steel washer (inside jaws) and press Open: the inside jaws spread until they touch the wall of the hole.
- Set Mode to Practice. Press Check zero, then Back, read both scales, type the true size and press Check.