Skip to content

Measurement and skills simulation

Micrometer Screw Gauge Simulation

Close a chrome micrometer on a copper wire, a steel ball bearing, a sheet of paper or a coin, and read it to 0.01 mm. A close-up of the sleeve and thimble lights up the marks that matter, and practice mode tells you which slip you made.

Loading simulation…
Show symbols for

Predict first

Question 1 of 4

This micrometer's screw has a pitch of 0.5 mm and its thimble has 50 divisions. The jaws are open, and the thimble is turned through exactly one complete turn. How far does the spindle move?

Try this

  1. 1The sim opens with a steel ball bearing gripped. In the close-up, the glowing sleeve mark is labelled 7.5 mm and the glowing thimble division is labelled 44. Does 7.5 mm + 44 × 0.01 mm match the Observed reading card?
  2. 2Press Open, then Ratchet. Watch the thimble wind in, and look for the ratchet's clicks once the spindle meets the ball.
  3. 3Choose Nothing (check the zero) in the Between the jaws menu, pick Negative (zero above the line) under Zero error and press Ratchet. In the close-up, count the divisions from the datum line up to the thimble's 0, then compare your count with the note under the Zero error buttons.
  4. 4Select the stage and press Page Up once, or press the + button fifty times. How much does the reading grow for one full turn of the thimble?
  5. 5Switch to Practice. Press Zero check (the 0 button under the stage) and read the closed jaws. Press the same button again to measure, then type your corrected reading and press Check. Press New object for another one.

What this simulation shows

A micrometer screw gauge reads small lengths to 0.01 mm, a tenth of a school vernier calliper's least count. It is the tool for the diameter of a wire, the thickness of a sheet of paper or the size of a ball bearing. Here you turn the thimble yourself, by dragging it, with the slider or the arrow keys, and the spindle winds towards the anvil. The ratchet closes the jaws gently and clicks when they grip.

Below the instrument, a close-up shows the sleeve and thimble at a size you can read on a phone. Every line in it is placed from the reading itself, so the division that glows on the datum line really is the one the gauge is showing.

Pitch and least count

Inside the barrel is a fine screw. One complete turn of the thimble moves the spindle by one pitch, which is 0.5 mm on the usual school instrument. The bevelled edge of the thimble is marked with 50 equal divisions, so turning it by one division moves the spindle by a fiftieth of the pitch.

least count=pitchnumber of thimble divisions=0.5 mm50=0.01 mm\text{least count} = \frac{\text{pitch}}{\text{number of thimble divisions}} = \frac{0.5\ \text{mm}}{50} = 0.01\ \text{mm}

Some gauges use a 1 mm pitch with 100 divisions instead. Switch the instrument in the controls and the least count stays the same.

Taking a reading

  1. Look at the sleeve. Find the last mark the thimble edge leaves uncovered. Whole millimetres are above the datum line and half millimetres are below it. This gives the main scale reading.
  2. Look at the thimble. Read the division sitting level with the datum line. This is the circular scale reading.
  3. Multiply the division by the least count and add it on.

reading=main scale reading+circular reading×least count\text{reading} = \text{main scale reading} + \text{circular reading} \times \text{least count}

The half-millimetre mark catches many people out. If one is showing after the last whole millimetre, add 0.5 mm before the thimble value. A circular reading close to 0 with a mark just appearing, or one in the high 40s with a mark just hidden, are the readings to check twice.

Zero error

Before measuring, close the empty jaws with the ratchet. On a perfect gauge the thimble zero stops on the datum line. If it stops below the line, the instrument already reads a little above zero, so every result comes out too big: a positive zero error. If the thimble turns past zero and stops with its zero above the line, it reads too little: a negative zero error, found by counting divisions from the line up to the zero.

corrected=observed−zero error\text{corrected} = \text{observed} - \text{zero error}

So a positive error is taken away and a negative one ends up added. In the Punjab Class 9 book the rule is given in words, with the datum line called the horizontal line: zero below that line, subtract the error; zero above it, add the error. Whenever the gauge has a zero error, the readout cards show this subtraction with its signs.

Very thin objects

A single sheet of paper is only about ten least counts thick. Stacking many sheets, measuring the stack and dividing by the number of sheets gives a far more precise value for one sheet.

Practice mode

In Practice the object and its size are chosen at random, and some gauges come with a zero error. Press Zero check (the 0 button under the stage) to read the closed jaws, then press it again to measure. Type the corrected reading and the feedback names your slip: a missed half mark, a forgotten or reversed zero error, the wrong least count or a misread thimble.

Check your understanding

8 questions

  1. 1.A micrometer screw has a pitch of 0.5 mm and the thimble carries 50 divisions. What is its least count?
  2. 2.The last whole-millimetre mark showing on the sleeve is 4 mm, and the half-millimetre mark after it is also showing. Division 18 is on the datum line. What is the reading?
  3. 3.The thimble edge has passed the 9 mm mark, but the half mark after it is still hidden. Division 47 is on the datum line. What is the reading?
  4. 4.With the jaws closed, the zero of the circular scale stops 2 divisions below the datum line. A rod then gives an observed reading of 3.56 mm. What is its true diameter?
  5. 5.With the jaws closed, division 46 sits on the datum line and the zero is above it. A wire gives an observed reading of 1.21 mm. What is the wire's true diameter?
  6. 6.Why is a micrometer closed with the ratchet instead of by turning the thimble directly?
  7. 7.On a micrometer with a 1 mm pitch and 100 thimble divisions, the jaws are opened from closed by 3 full turns and 25 more divisions. How far apart are the jaws?
  8. 8.A stack of 100 identical sheets of paper measures 9.80 mm. What is the thickness of one sheet?

For teachers

Embed it in your site or open it full-screen for the projector.

Read more