Skip to content

Punjab Board Class 9 Physics · Magnetism

Magnetisation and demagnetisation

Section 8.9

A steel bar is magnetised when its domains line up: stroke it with a magnet by the single or double touch method, or put it in a solenoid carrying d.c. and find its N end with the right-hand grip rule. Strong heating, hammering or slow withdrawal from an a.c. solenoid demagnetises it.

Loading simulation…

Symbols match your course. Open the full magnetic field around a wire and solenoid simulation for more presets and teacher tools.

Lining up the domains

Section 8.8 pictures a ferromagnetic material as tiny regions called magnetic domains, each a small magnet. In an unmagnetised steel bar they point in random directions and cancel out. Magnetisation turns most of them to face one way; demagnetisation scatters them again. Steel resists: only a strong field turns its domains. Once turned, though, they keep their new direction, so magnetised steel stays a magnet.

Method 1: stroking

Lay the steel bar flat on a horizontal surface.

  • Single-touch method: run one pole of a permanent magnet (the N pole, for example) along the whole bar, end to end. Lift it well clear and carry it back to the start, so every stroke goes the same way. Repeat several times.
  • Double-touch method: place the N pole of one permanent magnet beside the S pole of another at the middle of the bar. Slide both outwards together, towards opposite ends. Your book rates this as more efficient.

Each end of the bar takes the pole opposite to the one that stroked towards it: stroke towards end B with an N pole, and B becomes S.

Method 2: inside a solenoid

Put the steel bar inside a long coil of insulated copper wire with a few hundred turns, and pass a direct current through it. The steady field lines up the domains, and the bar stays magnetised after the current is switched off.

To predict the poles, use the right-hand grip rule: wrap your right hand round the solenoid with your fingers following the current through the turns, from the battery's + terminal towards its − terminal. Your thumb, along the bar, shows its N end.

Worked example: making end P the N pole

A steel bar PQ lies inside a solenoid, P on the left. Which way must the current go round the turns for P to become N?

  1. The thumb must point at P, so point your right thumb left.
  2. Your fingers curl round the coil. Looking at end P from the left, they turn anticlockwise.
  3. So the current must circle anticlockwise as seen from P. Connect the battery that way round, switch on briefly, then off.
  4. Test with a compass: P should repel the needle's N end. Only a magnet repels, so P is N.

Reversing the battery would make P an S pole.

Demagnetising a magnet

Knock the domains out of line and a magnet is demagnetised. The book gives three ways:

  1. Heating: heat it strongly. Its atoms vibrate harder, the neat order of the domains breaks down, and the magnetism vanishes quickly.
  2. Hammering: strike it hard, again and again. The jolts knock the domains out of alignment.
  3. Alternating current: pass a.c. through a long solenoid, hold the magnet inside, then draw it out slowly until it is well away. The reversing field flips the domains to and fro, more weakly as the magnet moves out, until they are left pointing at random.

D.c. would not work: it would just magnetise the bar again, one way.

Magnetising steel on screen

In the simulation above, skip Straight wire, which is beyond Class 9, and choose Solenoid. Its switch is already on, so a direct current flows from the cell.

  1. Pick Steel under Core. N pole reads Right-hand end: seen from the right, the current runs anticlockwise round the turns, and your right thumb points right.
  2. Press Switch to stop the current. The card still reads Right-hand end: the steel is now a permanent magnet.
  3. Press Demagnetise. An a.c. flows and fades to nothing, flipping the steel's magnetism to and fro more weakly each time; then the card reads None. Your book instead draws the magnet slowly out of an a.c. coil; both ways, the field it feels reverses and fades.
  4. Pick Soft iron and press Switch to turn the current on: Right-hand end. Press Switch again: straight back to None, as soft iron is only a temporary magnet.
  5. Choose Electromagnet and pick Steel. Set Turns to 400 and Current to 5 A, then press Switch to turn the current on: 19 clips. Press Switch again: 5 stay on the steel. Demagnetise drops them.

Field values in teslas are extras beyond Class 9.

Common mistakes

  • Stroking the bar back and forth. In the single-touch method every stroke goes the same way, and the magnet is lifted well clear before it returns to the start.
  • Using two like poles in the double-touch method. The two magnets start together at the middle of the bar with unlike poles, then move apart towards opposite ends.
  • Thinking the end where an N-pole stroke finishes turns into an N pole. It ends up as an S pole: each end takes the opposite polarity to the stroking pole.
  • Using a.c. to magnetise a bar in a solenoid. A.c. keeps reversing, so it is used to demagnetise; a direct current is needed to magnetise.
  • Pulling the magnet out of the a.c. solenoid quickly, or switching the a.c. off with the magnet still inside. It must be withdrawn slowly to a distance, so that the reversing field it feels dies away gradually.
  • Curling the fingers along the electron flow, or using the left hand, in the grip rule. Use the right hand with the fingers along the conventional current, from + to −, and the thumb gives the N end.

Exam-style questions

Original questions written in the style of Punjab board exams. Try each one before you reveal the answer.

  1. 1.Answer these short questions.

    1. (a)What is meant by magnetisation and demagnetisation?

      2 marks
      Show the answer

      Answer: Magnetisation is making a magnetic material, such as a steel bar, into a magnet by lining up its domains. Demagnetisation is removing the magnetism of a magnet, so that its domains point in random directions again.

      Marking points

      • Magnetisation: making a material into a magnet (domains lined up)
      • Demagnetisation: destroying a magnet's magnetism (domains made random)
    2. (b)Name two methods of magnetising a steel bar.

      2 marks
      Show the answer

      Answer: Stroking it with a permanent magnet (single-touch or double-touch method), and placing it inside a solenoid that carries a direct current.

      Marking points

      • Stroking (single or double touch)
      • Inside a solenoid carrying d.c. (electrical method)
    3. (c)Why does strong heating demagnetise a magnet?

      2 marks
      Show the answer

      Answer: Heating makes the atoms vibrate more strongly. These thermal vibrations upset the alignment of the domains, which end up in random directions.

      Marking points

      • Heating increases the vibration of the atoms
      • The alignment of the domains is destroyed (they become random)
    4. (d)Why is a.c., and not d.c., used to demagnetise a magnet with a solenoid?

      2 marks
      Show the answer

      Answer: A.c. keeps reversing, so it turns the domains back and forth; as the magnet is withdrawn, the swings get smaller until the domains are left random. D.c. would magnetise the bar in one direction instead.

      Marking points

      • A.c. reverses direction, flipping the domains to and fro (until they are left random)
      • D.c. would magnetise the bar in one direction
  2. 2.A steel bar AB is to be magnetised by the single-touch method, using the N pole of a bar magnet. Each stroke starts at end A and finishes at end B.

    1. (a)Describe how the stroking is done.

      3 marks
      Show the answer

      Answer: Place the bar on a horizontal surface. Stroke it from A to B with the N pole of the magnet, always in the same direction, several times. After each stroke, lift the magnet high above the bar before bringing it back to A.

      Marking points

      • Bar on a horizontal surface, stroked from A to B with the N pole
      • Always in the same direction, repeated several times
      • Magnet lifted well clear of the bar on the way back to A
    2. (b)Name the pole formed at end B.

      1 mark
      Show the answer

      Answer: An S pole.

      Marking points

      • S pole
    3. (c)How is the double-touch method different?

      2 marks
      Show the answer

      Answer: Two permanent magnets are used, with unlike poles placed together at the centre of the bar. They are moved apart at the same time, from the centre towards the two ends.

      Marking points

      • Two magnets with unlike poles, starting at the centre of the bar
      • Moved apart at the same time towards opposite ends
  3. 3.A steel bar XY is placed inside a solenoid of several hundred turns, with end X on the left. The solenoid is joined to a battery through a switch.

    1. (a)What type of current should be passed through the solenoid? Give a reason.

      2 marks
      Show the answer

      Answer: Direct current (d.c.). Its field always points the same way, so it lines the domains up in one direction; a.c. would demagnetise the bar.

      Marking points

      • Direct current (d.c.)
      • Its field stays in one direction, so the domains are lined up one way
    2. (b)Explain how the right-hand grip rule is used to find the polarity of the bar.

      2 marks
      Show the answer

      Answer: Hold the solenoid in the right hand with the fingers curled the same way as the conventional current in the turns. The thumb then shows which end of the bar is N.

      Marking points

      • Right hand round the solenoid, fingers curled along the (conventional) current
      • The thumb shows the N end of the bar
    3. (c)Seen from end Y, the current goes round the turns clockwise. Name the poles formed at X and Y.

      2 marks
      Show the answer

      Answer: Y becomes an S pole, because the current looks clockwise from that end. X becomes an N pole.

      Marking points

      • Y: S pole
      • X: N pole
    4. (d)The current is switched off and the bar is taken out. Why does it stay a magnet?

      1 mark
      Show the answer

      Answer: Steel keeps the alignment of its domains once they have been turned, so it is a permanent magnet.

      Marking points

      • Steel keeps its domains aligned (steel makes permanent magnets)
  4. 4.A teacher wants to demagnetise an old bar magnet without heating it.

    1. (a)Describe how the teacher can demagnetise the magnet using a solenoid.

      3 marks
      Show the answer

      Answer: Pass an alternating current through a long solenoid. Place the magnet inside it. With the a.c. still flowing, pull the magnet out slowly and take it well away from the solenoid.

      Marking points

      • A.c. passed through a (long) solenoid
      • Magnet placed inside the solenoid
      • Magnet withdrawn slowly to a distance while the a.c. is still on
    2. (b)Explain, in terms of domains, why this method works.

      2 marks
      Show the answer

      Answer: The a.c. field reverses many times a second, turning the domains back and forth. As the magnet moves away the field it feels gets weaker, so the domains are left pointing in random directions.

      Marking points

      • The reversing field turns the domains back and forth
      • The field gets weaker as the magnet moves away, leaving the domains random
    3. (c)Name one other method the teacher could use, without heating the magnet.

      1 mark
      Show the answer

      Answer: Hammering it: beating it hard, again and again.

      Marking points

      • Hammering (beating) the magnet

Quick check

6 questions

  1. 1.A steel bar is stroked from end P to end Q, always with the N pole of a magnet (single touch). End Q becomes:
  2. 2.To magnetise a steel bar placed inside a solenoid, the solenoid must carry:
  3. 3.A bar magnet is heated strongly. Its magnetism:
  4. 4.The right-hand grip rule is used to find:
  5. 5.In the a.c. method of demagnetising, the magnet is:
  6. 6.Compared with soft iron, the domains of steel: