Skip to content

Punjab Board Class 9 Physics · Dynamics

Friction

Section 3.8

Friction opposes motion between surfaces. Sliding friction is static (F_s, equal to the pull up to the limiting friction) or kinetic (while sliding). Rolling friction is far smaller. Friction wastes energy as heat, and is reduced by polishing, lubricants, ball bearings and streamlining.

Loading simulation…

Symbols match your course. Open the full static and kinetic friction simulation for more presets and teacher tools.

What is friction?

A carrom striker flicked across the board soon stops. The force that stops it is friction: a force that opposes the motion of one surface over another, or a body's tendency to start moving.

Friction is a dissipative force. Work done against it turns useful energy into heat, which is lost. Rubbed palms warm up, and a drill bit gets hot as it bores into wood.

Sliding friction: static and kinetic

Friction between two solid surfaces is called sliding friction. It has two kinds, static and kinetic.

  • Static friction (FsF_s) acts on a body that is being pulled or pushed but has not started moving. It is only as large as it needs to be: while the body stays at rest, FsF_s is equal and opposite to the applied force.
  • Limiting friction is the greatest value static friction can reach. Pull harder than this and the body starts to slide.
  • Kinetic friction acts while the body is sliding. It is usually a little smaller than the limiting friction, which is why a heavy almirah is hardest to push at the very start.

Worked numerical 1: pushing an almirah

A 40 kg almirah stands on a level floor. Its limiting friction is 160 N and its kinetic friction is 120 N. Find the friction and the acceleration for a push of (a) 100 N and (b) 200 N.

(a) 100 N is less than the limiting friction, so the almirah stays at rest. Static friction balances the push: Fs=100 NF_s = 100\ \text{N} and a=0a = 0.

(b) 200 N is more than 160 N, so the almirah slides and kinetic friction (120 N) acts.

F=200−120=80 NF = 200 - 120 = 80\ \text{N} a=Fm=8040=2 m s−2a = \frac{F}{m} = \frac{80}{40} = 2\ \text{m s}^{-2}

To keep it sliding at a constant velocity, the push must equal the kinetic friction, 120 N.

Rolling friction

When a body rolls over a surface instead of sliding, the friction is called rolling friction. It is much smaller than sliding friction; your textbook puts it at roughly one hundredth. The part of a wheel touching the ground is at rest on it for an instant, so the two surfaces do not rub past each other, and they touch over only a tiny patch. That is why a wheeled suitcase is easier to move than one dragged flat, and why machines use ball bearings.

Friction: useful and harmful

UsefulHarmful
Lets us walk and run without slippingWastes energy as heat in engines and machines
Brakes and tyres stop vehicles; tread grooves keep tyres gripping wet roadsWears out tyres, shoe soles and moving parts
Holds nails and screws in place, and lets a pencil writeMeans extra fuel is burnt to overcome it

Ways to reduce friction

  1. Polish surfaces that slide over each other, so they are smoother.
  2. Lubricate them with oil or grease. Friction in a liquid is much less than between dry solids.
  3. Use ball bearings or wheels, which change sliding into rolling.
  4. Streamline cars, aeroplanes and boats so that air or water flows smoothly past them.

Worked numerical 2: braking

A 1200 kg car moving at 20 m s−120\ \text{m s}^{-1} brakes. On a dry road the friction from the road is 6000 N; on a wet road with worn tyres it is only 3000 N. Find the stopping time in each case.

Dry: a=−60001200=−5 m s−2t=vf−via=0−20−5=4 s\text{Dry: } a = -\frac{6000}{1200} = -5\ \text{m s}^{-2} \qquad t = \frac{v_f - v_i}{a} = \frac{0 - 20}{-5} = 4\ \text{s} Wet: a=−30001200=−2.5 m s−2t=0−20−2.5=8 s\text{Wet: } a = -\frac{3000}{1200} = -2.5\ \text{m s}^{-2} \qquad t = \frac{0 - 20}{-2.5} = 8\ \text{s}

Using the simulation

In the simulation above, a 2 kg Wooden block on wood rests on a bench and the Normal contact force reads 20.0 N (g = 10 N/kg). Press Pull beside Play: the pull grows by 2 N every second. While the block stays still, the Friction readout copies the pull and says static, can reach 10.0 N. That is static friction, and 10.0 N is the limiting friction.

Just after the pull passes 10.0 N the block slips, and the stage reports that friction drops from 10.0 N to 6.00 N, the kinetic friction. Press Pull again to hold the force: the block keeps speeding up. Now drag the Applied force slider down to 6 N. The resultant force is zero and the block slides at a steady speed.

Change Block on surface to Steel block on ice. The Limit line on the Friction against applied force graph falls to 0.800 N: smoother surfaces give less friction. Rubber block on concrete raises it to 20.0 N. The coefficients μs and μk shown in the simulation are a model detail; your course does not ask for them. The simulation has no wheels, so it does not show rolling friction.

Common mistakes

  • Thinking static friction always has its largest value. It is only as big as the pull; it reaches the limiting friction just before the body slides.
  • Drawing friction in the direction of motion. Friction always opposes the motion, or the attempted motion.
  • Putting the full pull into F = ma for a sliding body. Use the net force: pull minus kinetic friction.
  • Thinking kinetic friction grows when the body is pulled harder. While a body slides on the same surface, kinetic friction stays the same.
  • Saying wheels remove friction. Rolling friction is much smaller than sliding friction, but it is not zero.
  • Calling friction only harmful. Without it we could not walk, write, or stop a vehicle with its brakes.

Exam-style questions

Original questions written in the style of Punjab board exams. Try each one before you reveal the answer.

  1. 1.A heavy box rests on a level floor. A student pushes it gently at first, then harder until it moves.

    1. (a)What is meant by static friction and limiting friction?

      2 marks
      Show the answer

      Answer: Static friction is the friction acting on a body that is pushed or pulled but is still at rest; it balances the applied force. Limiting friction is the maximum value of static friction, reached just before the body starts to slide.

      Marking points

      • Static friction: acts while the body is at rest, opposing the applied force
      • Limiting friction: the maximum value of static friction
    2. (b)State two differences between static friction and kinetic friction.

      2 marks
      Show the answer

      Answer: Static friction acts before motion starts and changes to match the applied force; kinetic friction acts while the body slides and stays constant on a given surface. Kinetic friction is usually smaller than the limiting friction.

      Marking points

      • Static acts at rest and equals the applied force; kinetic acts during sliding and stays constant
      • Kinetic friction is less than limiting (maximum static) friction
  2. 2.A 25 kg crate rests on a level floor. The limiting friction on it is 90 N and the kinetic friction is 70 N. Take g = 10 N/kg.

    1. (a)A horizontal push of 60 N acts on the crate. State whether it moves, and give the friction force.

      2 marks
      Show the answer

      Answer: 60 N is less than the limiting friction (90 N), so the crate does not move. Static friction is 60 N, opposite to the push.

      Marking points

      • Does not move (60 N less than 90 N)
      • Friction = 60 N
    2. (b)The push is increased to 110 N. Calculate the acceleration of the crate.

      3 marks
      Show the answer

      Answer: The crate slides, so kinetic friction (70 N) acts. Net force = 110 − 70 = 40 N. a = F/m = 40 ÷ 25 = 1.6 m s⁻².

      Marking points

      • Kinetic friction 70 N used
      • Net force = 40 N
      • a = 1.6 m s⁻²
    3. (c)What push keeps the crate sliding at a constant velocity?

      1 mark
      Show the answer

      Answer: 70 N, equal to the kinetic friction, so the net force is zero.

      Marking points

      • 70 N
  3. 3.Wheels and ball bearings are used to make machines and vehicles easier to move.

    1. (a)Explain why rolling friction is less than sliding friction.

      2 marks
      Show the answer

      Answer: The part of a rolling wheel in contact with the surface does not slide over it (no relative motion at the contact), and the area of contact is very small.

      Marking points

      • No sliding / relative motion at the point of contact
      • Very small area of contact
    2. (b)Describe a simple experiment, using a heavy book, a rubber band and some round pencils, to compare rolling and sliding friction.

      3 marks
      Show the answer

      Answer: Pull the book across a table with the rubber band and note the stretch of the band. Place the book on the round pencils and pull it again. The band stretches much less, so a smaller force is needed: rolling friction is less than sliding friction.

      Marking points

      • Pull the book directly on the table and note the stretch of the band
      • Repeat with the book resting on round pencils
      • Less stretch on the pencils, so rolling friction is smaller
  4. 4.Friction is a dissipative force, so engineers try to reduce it in machines.

    1. (a)Why is friction called a dissipative force?

      1 mark
      Show the answer

      Answer: Work done against friction changes useful energy into heat, which is wasted.

      Marking points

      • Energy is wasted as heat
    2. (b)State three methods of reducing friction.

      3 marks
      Show the answer

      Answer: Polishing the surfaces; lubricating with oil or grease; using ball bearings so that sliding becomes rolling. (Streamlining reduces air or water resistance.)

      Marking points

      • Polishing the surfaces
      • Lubricating with oil or grease
      • Ball bearings (changing sliding to rolling) / streamlining

Quick check

6 questions

  1. 1.The maximum value of static friction is called:
  2. 2.A table is pushed with a horizontal force of 30 N but does not move. The static friction on it is:
  3. 3.Ball bearings reduce friction because they:
  4. 4.A crate slides across a floor while pushed with a force equal to the kinetic friction on it. The crate:
  5. 5.Oil is put between the moving parts of a machine mainly to:
  6. 6.For the same heavy load on the same floor, which friction is smallest?